Norsat O3b 10W BUC User Manual

Ka-band BUC 10W7010STC-O3bInstallation and Operation ManualDOC#038412 Rev. 1.0IMPORTANT NOTE: The information contained in this document supersedesall

© 2013 Norsat International Inc. Page 10 of 26OUTLINE DRAWING3.2Figure Figure 5. Mechanical outline for Ka band 10W BUC

© 2013 Norsat International Inc. Page 11 of 264 INSTALLATIONThis section of the manual is intended to provide aid in BUC installation.UNPACKING4.1Perf

© 2013 Norsat International Inc. Page 12 of 26The BUC has body and cover heat sinks with fins for air cooling. Therefore, to achieve an optimalfunctio

© 2013 Norsat International Inc. Page 13 of 26c) Repeat the steps above for all the connectors.5 EQUIPMENT OPERATIONUSER SOFTWARE INSTALLATION5.1The u

© 2013 Norsat International Inc. Page 14 of 26Figure 8. User software installation starting windowClick on NEXT to continue. You can accept the defaul

© 2013 Norsat International Inc. Page 15 of 26Figure 9. (2) User software installation proceeding windowFigure 9. (3) User software installation proce

© 2013 Norsat International Inc. Page 16 of 26Figure 9. (4) User software installation completion windowOnce the user software installation on your PC

© 2013 Norsat International Inc. Page 17 of 26o SSPA On functiono This button is used to turn on the SSPA of the BUC.o SSPA Off function (Mute)o This

© 2013 Norsat International Inc. Page 18 of 269iprdiprdRead BUC ip10portwrportwr 3000Write BUC port11portrdportrdRead BUC port12gwwrgwwr 192 168 100 1

© 2013 Norsat International Inc. Page 19 of 26Figure 12. BUC GUI window for operationSelect a usable COM port and the baud rate of 57,600 and click th

© 2013 Norsat International Inc. Page 2 of 26This page is intentionally blank.

© 2013 Norsat International Inc. Page 20 of 26Ethernet Mode Operation5.2.4For Ethernet mode operation, connect a prepared Ethernet cable between the M

© 2013 Norsat International Inc. Page 21 of 26- Serial command: gwwr 192 168 100 1 (Write Command)- Serial command: gwrd (Read Command)Step 4. Set up

© 2013 Norsat International Inc. Page 22 of 26Figure 16. PC parameters entry on BUC GUI window for Ethernet operationIf the Ethernet port is open, BU

© 2013 Norsat International Inc. Page 23 of 264) Turn on the power supply to supply +48V to the BUC.5) Set up the serial mode or Ethernet mode connect

© 2013 Norsat International Inc. Page 24 of 266 MAINTENANCE AND TROUBLE SHOOTINGMAINTENANCE6.1Ka band 10W BUC is designed for a minimum of maintenance

© 2013 Norsat International Inc. Page 25 of 26- Or, the BUC is faulty Contact Norsat for further support.4) When External Mute became red on the BUC

© 2013 Norsat International Inc. Page 26 of 26Contact: NORSAT INTL INC6.3110-4020 VIKING WAYRICHMOND BC V6V 2L4 CANADATOLL FREE: 1 800 644 4562FAX:

© 2013 Norsat International Inc. Page 3 of 26Table of ContentsTable of Contents ...

© 2013 Norsat International Inc. Page 4 of 26Installation Requirements...

© 2013 Norsat International Inc. Page 5 of 26Figure 1. Functional Block Diagram of Ka-band 10W BUCIF unit1.2.1IF unit amplifies the transmission signa

© 2013 Norsat International Inc. Page 6 of 26DC M&C Unit1.2.5This board includes a DC/DC converter, regulators, and a EMI/EMC filter to make all k

© 2013 Norsat International Inc. Page 7 of 26Equipment Working Conditions1.3.7Never perform maintenance or make adjustments to the BUC when the power

© 2013 Norsat International Inc. Page 8 of 26Figure 3. WR28 RF output port for Ka-band 10W BUCJ3 / DC, M&C2.3MS 12-pin connector is used for the D

© 2013 Norsat International Inc. Page 9 of 263 TECHNICAL SPECIFICATIONSSPECIFICATIONS SHEET3.1